Thermostat Housing Bolts Torque

HVAC System Torque Specifications HVAC SYSTEM TORQUE SPECIFICATIONS Application Ft. Can someone with a book look that up for me.

Bolt Up Of The Thermostat Housing Looked But Did Not Find A Torque Spec Opel Projects

Jump to Latest Follow 1 - 3 of 3 Posts.

Thermostat housing bolts torque. First I looked for rentals or loaners that I could use for the application only and give back but nothing I can tell is available. Water Inlet Housing Bolts 11 Lb Ft. Nm Balance Shaft Retainer Plate Bolts 43L 106 12 Camshaft Retainer Bolt 106 12 Front Cover Bolt 106 12 Intake Manifold Upper 43 Step 1 44 5 Step 2 88 10 Upper 50 57 Step 1 44 5 Step 2 88 10.

So either its a crappy water pump housing or the FSM is wrong I will. Jump to Latest Follow 1 - 8 of 8 Posts. I just tried to torque my thermostat housing bolts to 108 foot pounds what the Haynes Manual gives and it snapped clean before I got anywhere near there.

The valve cover on my 18 has that spec too. Search Car Torque Specifications by Engine or Model. Timing belt tensioner bolt idler pulley bolt.

The seal is split on the inside surface so that it wraps around the thermostat flange and covers the flange edge both top and bottom. Bell Housing Cover To Bell Housing 75 Ft-Lbs 90. Torque specs according to Alldata.

Thermostat Housing Bolt 21 28 Valve Lifter Retainer Bolt 43L 12 16 50L 57L 18 25 Water Pump Bolt 33 45 INCH Lbs. Thermostat Housing Cover To Thermostat Housing 18 Ft-Lbs 216 In-Lbs 244 N-m Years. Over 6000 Automotive Torque Specs.

Timing belt cover bolts. Tightening torque Coolant temperature sensor 20 - 40 Nm 200 - 400 kgcm 15 - 30 ft. Valve Cover To.

Thermostat cover - 2 bolts. Housing bolt torque is 47 ft-lbs. The thermostat housing torque spec is 71 inch-pounds.

Thermostat Housing BoltNut 18 25 Thermostat Cover Bolt 15 21 Turbocharger Bolt 80 108. Cylinder head bolts must be done in stages and in correct order. In some cases on the valve cover I was reluctant to go that tight.

If you dont have a torque wrench then you should be safe with getting the bolts snug tight then about a 14 turn after that. Thermostat housing torque settings needed Hey all. The water outlet spec is also 71 inch-pounds.

I was afraid I was going to strip something and stopped around 50 inch-pounds. Well when installing the new water pump the freaking water pump housing broke at the bolt in two locations. The 12-14 ft-lbs on the water pump seems like an excessive amount.

Nm AC Refrigerant Filter Retaining Nuts 11 15 Compressor Bracket Mounting Bolts 37 50. 71 inch-pounds is a pretty common spec on these cars. Can someone tell me please.

Vortec - Torque Converter to Flywheel Bolts Type. Id really prefer to not strip those threads. Water pump pulley - 3 bolts.

I wouldnt try getting anywhere near that much torque on a bolt that size. Water pump housing pulley bolts and Thermostat housing bolts torque specs. Torque for thermostat housing.

Water inlet pipe - 2 bolts to water pump. Replace the top and bottom T30 Torx bolts. Discussion Starter 1 Feb 26 2013.

Thermostat Housing To Intake Manifold 30 Ft-Lbs 360. Radiator - upper bolts. There are 3 bolts that take no more than 8ft lbs of torque according to the Nissan shop manual.

Nothing critical there as long as the thermostat housing doesnt crack and the threads dont pull out of the intake. GM 57L-350ci-V8 Engine Torque Specs. I found a lot of info on replacing the thermostat housing.

I figure its a LOT more important to coat the living hell out of the thermostat housing bolt threads with anti-seize if youre working with an aluminum intake. I always run a tap thru the threads and a drill thru the housings to clean out any corrosion then put Neversize on the bolts and threads and torque to 30 to 35 ft lbs. Install the new thermostat housing in the same orientation as the one you just removed.

I believe these should be torqued to 105 in-lbs. I didnt find torque settings for the thermostat housing bolts however. Joined Jan 27 2013 6 Posts.

Joined Oct 29 2008 157 Posts. Dunno what I was thinking. My torque wrench doesnt go below 20 ft lbs.

Putting a new water pump and a new thermostat in my S14 KA24DE stock. Discussion Starter 1 Nov 19 2010. I dont have a manual yet and I need some torque specs.

Pin On New Automotive Performance Products From Wwww Autopressreleases Com

Tansky For Honda Civic Eg Ek Jdm Engine Billet Motor Torque Mount Kit B16 B18 B20 D16 D15 Tk M11 Honda Civic Civic Eg Jdm

Cool View Thermostats Built With High Strength Glass You Can See When Your Thermostat Is Open Or Closed Chevy Ford Ford Cool Stuff Veteran Car Sweet Cars